Zurück

Ausgabe des dmesg-Programms


Linux version 2.2.16 (root@Pentium.suse.de) (gcc version 2.95.2 19991024 (release)) #1 Wed Aug 2 20:22:26 GMT 
Detected 300687 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 599.65 BogoMIPS
Memory: 256892k/262080k available (1448k kernel code, 412k reserved, 2912k
data, 68k init, 0k bigmem)
Dentry hash table entries: 32768 (order 6, 256k)
Buffer cache hash table entries: 262144 (order 8, 1024k)
Page cache hash table entries: 65536 (order 6, 256k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium II (Klamath) stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xf0720, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 262144 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5 
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
RAM disk driver initialized:  16 RAM disks of 64000K size
loop: registered device at major 7
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA
hda: Maxtor 32049H2, ATA DISK drive
hdb: IBM-DHEA-36481, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: Maxtor 32049H2, 19541MB w/2048kB Cache, CHS=2491/255/63
hdb: IBM-DHEA-36481, 6197MB w/472kB Cache, CHS=790/255/63
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
LVM version 0.8e  by Heinz Mauelshagen  (4/1/2000)
lvm -- Driver successfully initialized
md driver 0.36.6 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
scsi : 0 hosts.
scsi : detected total.
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 >
 hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 hdb7 hdb8 >
RAMDISK: Compressed image found at block 0
Uncompressing................................done.
VFS: Mounted root (ext2 filesystem).
(scsi0)  found at PCI 0/12/0
(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
(scsi0) Downloading sequencer code... 415 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.31/3.2.4
       
scsi : 1 host.
(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
  Vendor: TEAC      Model: CD-R55S           Rev: 1.0K
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
(scsi0:0:2:0) Synchronous at 10.0 Mbyte/sec, offset 15.
  Vendor: IBM       Model: DFHS              Rev: 17  
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 2, lun 0
(scsi0:0:5:0) Synchronous at 10.0 Mbyte/sec, offset 15.
  Vendor: PLEXTOR   Model: CD-ROM PX-40TS    Rev: 1.01
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 5, lun 0
Uniform CD-ROM driver Revision: 3.11
sda: Spinning up disk...........ready
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2055035 [1003 MB] [1.0 GB]
 sda: sda1
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 68k freed
Adding Swap: 265064k swap-space (priority -1)
Serial driver version 4.27 with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.232 $ time 20:30:31 Aug  2 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: Intel USB controller: setting latency timer to 0
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 15
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
SB 4.13 detected OK (220)
eth0: 3c509 at 0x300 tag 1, 10baseT port, address  00 a0 24 14 82 4a, IRQ 5.
3c509.c:1.16 (2.2) 2/3/98 becker@cesdis.gsfc.nasa.gov.
eth0: Setting Rx mode to 1 addresses.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de)
nfsd_fh_init : initialized fhcache, entries=512
parport0: PC-style at 0x378 (0x778) [SPP,ECP,ECPEPP,ECPPS2]
parport_probe: failed
parport0: no IEEE-1284 device present.
ppa: Version 2.03 (for Linux 2.2.x)
ppa: Found device at ID 6, Attempting to use EPP 32 bit
ppa: Communication established with ID 6 using EPP 32 bit
scsi1 : Iomega VPI0 (ppa) interface
scsi : 2 hosts.
  Vendor: IOMEGA    Model: ZIP 100           Rev: L.01
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi removable disk sdb at scsi1, channel 0, id 6, lun 0
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
sdb: Write Protect is off
 sdb: sdb1